Menu

HEF4060 DATASHEET PDF

0 Comment

HEF Datasheet, HEF PDF, HEF Data sheet, HEF manual, HEF pdf, HEF, datenblatt, Electronics HEF, alldatasheet, free. 15 Apr Data sheet acquired from Harris Semiconductor. SCHSC − Revised October HCDB consists of an oscillator section and CMOS Stage Ripple-Carry Binary Counter/Divider and Oscillator. CMOS Stage Ripple-Carry Binary Counter/Divider and Oscillator – CDB. Datasheet.

Author: Arasar Kijora
Country: Bhutan
Language: English (Spanish)
Genre: Technology
Published (Last): 4 September 2016
Pages: 268
PDF File Size: 13.24 Mb
ePub File Size: 5.63 Mb
ISBN: 325-6-99652-421-6
Downloads: 29315
Price: Free* [*Free Regsitration Required]
Uploader: Kigalkree

This hef4060 datasheet you to accurately synchronize the clock with a known good time source. The Hardware Part 1 You can download the circuit diagram here.

Результаты поиска для HEF4060

C5 is used to set the correct frequency. There’s one output we might use though. It doesn’t really matter hef4060 datasheet we use a rising or falling edge here because this carry pulse is very short.

The output pulse from IC10A also goes out to the minutes counter, hef4060 datasheet has to be advanced at datasheett overflow of the seconds counter.

It is very important to use 0 tempco capacitor for C4. Everything is built on pad board using Road Runner wiring to connect all jef4060 components together.

Once the counters reach that hef4060 datasheet they are reset back to 0 again. I don’t need the output of the seconds counter itself, because I do not have a seconds display. It’s a bed heg4060 hef4060 datasheet clock, I don’t need it to light up the entire room at night, you know.

The Hours Counter And now the hours counter. This allows you to advance hef4060 datasheet hours counter. Both buttons have a debouncing capacitor in parallel to make sure that every button press results in just one pulse. When the clock is switched to SET mode though, hef4060 datasheet SET line goes low, which keeps the reset line to the seconds counter constantly high, preventing the seconds counter to count.

Most Related  FORM 50A WEST BENGAL DOWNLOAD

As usual, with such a one of project, I didn’t bother to create a PCB for the project. This page will describe sheet one in detail, while the next page will describe sheet number two. We haven’t talked hef4060 datasheet the carry from the seconds counter to the minutes datashet yet. Please consider clicking on the Support Me button to datwsheet your appreciation. But when the most significant digit hef4060 datasheet the hours counter increments the clock hef4060 datasheet of the flip-flop rises, which sets the flip-flop, making the Q output low.

It uses a It is spread over two sheets, one sheet covers the time base and the seconds, minutes and hef4060 datasheet counters.

This counter is also formed by 2 decade counters. The clock can be in one of two different modes, in Run mode hef4060 datasheet in Set mode. This pulse is very short because its cause is removed by the reset almost instantly.

Datawheet Minutes Counter Next stop, the minutes counter. IC4B tries to do the same for the 0. The precision of the resistor value has no effect on the precision of the time base B. It’s output Q0 of hef4060 datasheet first decade counter IC4A. I have covered the time base and the counters here. As a matter of fact, hef4060 datasheet no more on sheet number one to be explained. This reset pulse is also used as carry to the hours counter.

And now the hours counter. But this time the maximum count value is limited to The carry from the seconds counter is constantly high, with only a datashdet carry pulse every 60 hef4060 datasheet.

CDB CMOS Stage Ripple-Carry Binary Counter/Divider and Oscillator |

The Time Base IC2 forms the time base datashfet and first pre-scaler stage. In SET mode the SET signal is high, and the seconds to minutes carry can never occur because the seconds counter is held in reset. While the clock is in SET hef4060 datasheet there won’t come any carry pulses hef460 the minutes counter and that signal is constantly high. My way of keeping this site alive. Therefore IC3A is used to divide the frequency down hef4060 datasheet 1Hz. Let’s start simple, the buttons, which are used to set the time.

Most Related  OF WHITE HAIRS AND CRICKET BY ROHINTON MISTRY PDF

Therefore IC9C will hef4060 datasheet follow the low going carry signal from the minutes counter. Hef4060 datasheet Buttons Let’s datashdet simple, the buttons, which are used to set the time. You can download the circuit diagram here. Now IC9D will inverse datashwet pulses coming from the push hef4060 datasheet.

Next stop, the minutes counter. We are only interested in two others, the Hz and the 64Hz outputs, which are used in the display section of the clock. At the end it will produce an accurate frequency of 2Hz on output pin 3. IC2 also contains a 14 bit divider chain. Both inputs of IC10D are high when the button is pressed, making its output low.

However hef4060 datasheet would require hef4060 datasheet extra chip for just one gate, whereas I had a spare flip-flop available which could be ab used for the same job.

We’ll have to tell the clock what time it is when it has lost all its power anyway. IC2 forms the time base oscillator and first pre-scaler stage.